Markets in Motion: Momentum Analysis Assumes the Current Velocity of Price Change Offers Insight into the Future Direction of Price Change. Several Tools Measure These Changes and Suggest Ways You Can Position Your Trading Capital to Take Advantage of Those Changes

Article excerpt

Trading has many big questions, and one of the biggest is this: When a market is moving in a particular direction, is it more likely to keep moving in that direction, or is it poised to exhaust its momentum and turn or stall?

Momentum indicators, which measure the velocity of price changes and not necessarily the direction of price changes, dare traders to ask themselves that question constantly. That is, when the momentum indicator reports that prices are moving higher at an exceedingly faster rate, do you buy to go with the flow, or do you offset your longs or even sell on the assumption the market can't maintain such a high rate of change?

These indicators are typically displayed as oscillating lines beneath a price chart. As such, they often are referred to, in general, as oscillators. For most oscillators, positive values reflect rising prices and negative values reflect falling prices. The higher the positive value, the faster price is rising. The lower the negative value, the faster price is falling. Values near zero indicate the market is stagnant.

There are dozens of momentum indicators. However, they are all similar, with minor tweaks or twists. If you're new to them, however, it's sufficient to start with three: rate of change, stochastics and the relative strength index (RSI).


It seems passe to bother with indicator formulas more than two decades after the advent of modern technical analysis software. Nevertheless, seeing the mechanics behind the squiggly lines on the chart can offer insight that you might not otherwise have.

Rate of change (ROC) charts the close of the current period (minute, hour, day, week, etc.) as a percentage of the close a specified number of periods ago. An alternate calculation reports rate of change in percentage terms, dividing the difference between the two closes by the earlier of the two closes.

Here are the formulas:

ROC = (close_1 / close_n) * 100


ROC = ((close_1 - close_n) / close_n)

* 100

Reading the result of the formula is relatively simple. If the value on the oscillator is above 100%, this period's close is greater than the close n periods ago. If the rate-of-change value is less than 100%, this period's close is less than the close n periods ago. The extent to which the reading is higher or lower than 100%, the stronger the trend.

The relative strength index (RSI) was introduced by J. Welles Wilder in the June 1978 issue of Commodities magazine (now Futures) and was expanded on in Wilder's book "New Concepts in Technical Trading Systems," published that same year. RSI has since become one of the most popular technical indicators in use today.

According to Wilder's original Futures article:

RSI = 100 - 100 / 1 + RS, where

RS = Average of 14 days that closed up / Average of 14 days that closed down

In calculating the index, you start with 15 days of price data (not just 14 because the first day requires the previous close from which to determine the first up or down close value). Add up the amounts by which the market closed higher than the previous day and divide that by 14. Do the same with the amounts by which the market closed lower. Divide the average up close by the average down close to get RS. For example, if the sum of the day's up closes divided by 14 is 0.95 and the sum of the day's down closes divided by 14 is 0.33, RS is 2.9, and:

RSI = 100 - 100 / 1 + 2.9

RSI = 100 - 100 / 3.9

RSI = 100 - 25.6

RSI = 74.4

The RSI value for the next day, day 16, is calculated by multiplying the previous average up and down closes by 13, adding either the new up close or the new down close, and dividing each value by 14. This effectively smoothes the oscillator, reducing noise.

Stochastics is visually unique from ROC and RSI. Stochastics, developed by George Lane in the 1960s, uses multiple lines to determine momentum. …